Operating the EX500
EX500 MONO SUB WITH PASSIVE SATELLITES
If your system uses a standard stereo power amp and passive full range enclosures, like the Samson EX10, the
EX500 is easily interfaced for extended bass. Below is a typical system set-up using the EX500 with a mixer,
stereo power amp and a pair of passive satellite loudspeakers.The EX500Os inputs and outputs utilize industry
standard XLR connectors. For a detailed wiring diagram, see the section EX500 Connections on page 1. Follow
the steps below the diagram to set up your system.
EX10EX10
PL1602 Mixer
PL 160216 CHANNEL LINE MIXERSAMSON TECHNOLOGIES CORP., NEW YORK, U.S.A.
S / NPOWERINPUTS BALANCED 10Kä -30 to +4db TIP + RING - SLEEVE GND.MIC 1
110ONOFF+40TRIM-40-10312
16R15L14R13L12R11L10R9L8R7L6R5L4R3L2R1L
DO NOT EXPOSE THIS EQUIPMENTRISQUE DE CHOC ELECTRIQUENE PAS OUVRIRAVIS:0-1032
RATINGPOWERCAUTIONTO RAIN OR MOISTURE120V - 60 Hz 35WRMAIN OUTBUSLRL4R3LAUX2R1L2RAUX SEND1L6R5LINSERTS TIP RETURN RING SEND4R3L2R1LTRIMMIC 3+4-401
~115V(0.3A)230V(0.15A)50/60Hz 30WRISK OF ELECTRIC SHOCKDO NOT OPEN! TIP + RING - SLEEVE GND BALANCED 600 +4dbMIXER LINKINGINSERTSUNBALANCED 10K RETURNSäUNBALANCED 2Kä +4db
EX500
STEREO
105BALANCED INPUTSBALANCED HIGH PASS OUTPUTS
MONOYY0LEYYVEL10YY30Y5YSWEEPY200HzY YPEAKYMONOLEFTRIGHTLEFTRIGHTSTEREO
POWERED SUBWOOFER 500 WATTS
SAMSONEX500
ENGINEERED AND DESIGNED BY SAMSON IN THE UNITED TECHNOLSTATESOGIESSERIALNo.A.C. MAINS DO NOT EXPOSE THIS EQUIPMENTRISQUE DE CHOC ELECTRIQUETO RAIN OR MOISTURE.NE PAVIS;AS OUVRIRPOWERRATING60HzONPOWER
MADE IN CHINARISK OF ELECTRIC SHOCK115V/230V 50HZ/60Hz 500WCAUTION230V115VAACCDO NOT OPEN50HzOFF
Servo 550
CAUTIONSERVO 550 STUDIO AMPLIFIERSAMSON TECHNOLOGIES CORP., HICKSVILLE, NEW YORK RISK OF ELECTRIC SHOCKDO NOT OPEN!
EFUSESUFSERIALBRIDGED
FUSE RATING12A/250V (115V)NUMBERMONO STEREO
USE CLASS 2 WIRING MAXIMUM LOAD IMPEDANCE 46A/250V (230V)&LEFT
HOT! DO NOT BLOCK HEATSINK MAY BE CAUTION
TO PREVENT SHOCK DO NOT OPEN. NO USER SERVICABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE AIRFLOW OR OVER-HEATING MAY OCCUR+RIGHTOUTPUT 250W/4GROUND&LEFT+(BALANCED10KINPUTSRIGHT
PERSONNEL. TO PREVENT FIRE OR SHOCK HAZARD &/0dBm0)
TIP RING SLEEVE
RIGHTLEFT510W (115V)900W (230V)115V/230W, 50/60HZ~AC INPUTSLEEVE GNDTIP +RING -
YLower your mixerOs master outputs to all the way off.
YConnect the mixerOs left output to the EX500Os left input and the mixerOs right output to the EX500Os right
input. Now connect the EX500Os left outputs to the left side input of your power amp, and EX500Os right
output to the right side input of your power amp. Run your speaker cables from the power ampOs outputs
to the left and right satellite speakers. Switch the Stereo/Mono
selector switch to the MONO position.
YNow adjust the crossover SWEEP to the desired frequency.
BAL
For the Expedition EX20 & EX30 select 80-100Hz. If you areHz
5105
using another brand of powered speaker as satellites with theYYYY
PEAKSTEREO
EX500, consult their respective owners manuals for the recom-YY YY
MONO
mended crossover point.YYYY
010 30200
LEVELSWEEP
LEF
YSet the level of your power amplifiers to the normal operating
level. Run an audio signal (like some music from a CD) through
your mixer and raise the level to a comfortable listening volume.
Now, slowly raise the EX500 Level control and listen to the low
frequency output. Adjust the EX500 to the level of low frequen-
cy output that you like. Now when you raise and lower your
mixerOs output, the EX500 and satellites will track at the same
relative volume.
10 |